نوار کناری
برد رزبری پای Raspberry Pi Model +A
کد محصول: برد رزبری پای Raspberry Pi Model +A
موجودی در انبار(موجود)
تعداد بازدید 2283 بازدید
دسته بندی هاسبد خریدحساب کاربریجستجومشاهده های اخیر
همه دسته بندی ها×
- برد رزبری پای - RASPBERRY PI
- بردهای کاربردی تحت سیستم عامل
- بردهای کاربردی صنعتی
- تجهیزات الکترونیک
- تجهیزات جانبی
- تغذیه سوئیچینگ صنعتی-آداپتور-منبع تغذیه
- جعبه - کیس های مدار و برد
- دستگاه کنترل پیامک
- ماژول ها
- ISM Band
- LCD
- درایور موتور
- دوربین
- ماژول اثر انگشت
- ماژول دما و رطوبت
- ماژول سنسور گاز
- ماژول های GSM/GPS/GPRS
- ماژول های RFID
- ماژول های آلتراسونیک
- ماژول های بلوتوث
- ماژول های تایمر و پالس
- ماژول های تغذیه و ولتاژ
- ماژول های شبکه و WIFI
- ماژول های شتاب سنج و ژیروسکوپ
- ماژول های صوتی و آمپلی فایر
- ماژول های فرستنده و گیرنده
- ماژول های فشار
- ماژول های مبدل
- ماژول های پزشکی و ضربان قلب
- ماژول های کاربردی
- ماژول پرینتر
- موتورها
- پروگرامرها
- کتاب های آموزشی و کاربردی
- کیت های آموزشی
- بردهای آموزشی ARM , AVR , PIC , FPGA
- روباتیک
- آردوینو
- سنسورها
- LED
- ریموت و کنترل کننده های صنعتی و کاربردی
- آنتن ها
- قطعات پروازی و ربات های پرنده
سبد خرید×
سبد خرید شما خالی است !
جستجو×
محصولاتی که بازدید کرده اید.×
توضیحات محصول
رسپبری پای مدل A+ مناسب برای کاربردهایی با عدم نیاز به دسترسی به اینترنت و اتصالات USB زیاد
The Model A+ is the low-cost variant of the Raspberry Pi. It replaced the original Model A in November 2014. Compared to the Model A it has:
-More GPIO. The GPIO header has grown to 40 pins, while retaining the same pinout for the first 26 pins as the Model B.
-Micro SD. The old friction-fit SD card socket has been replaced with a much nicer push-push micro SD version.
-Lower power consumption. By replacing linear regulators with switching ones we’ve further reduced power consumption.
-Better audio. The audio circuit incorporates a dedicated low-noise power supply.
-Smaller, neater form factor. We’ve aligned the USB connector with the board edge, moved composite video onto the 3.5mm jack, and added four squarely-placed mounting holes. Model A+ is approximately 2cm shorter than the Model A.
We recommend the Model A+ for for embedded projects and projects which require very low power, and which do not require Ethernet or multiple USB ports.
- Broadcom BCM2835 700MHz ARM1176JZFS processor with FPU and VideoCore IV dual-core GPU
- GPU provides Open GL ES 2.0, hardware-accelerated OpenVG, and 1080p30 H.264 high-profile decode
- GPU is capable of 1Gpixel/s, 1.5Gtexel/s or 24GFLOPs with texture filtering and DMA infrastructure
- 256MB SDRAM
- HD 1080p video output
- Composite video (PAL/NTSC) output
- Stereo audio output
- HDMI 1.3 & 1.4 video/audio socket
- 3.5mm 4-pole audio/composite video out jack socket
- 1 x USB 2.0 socket
- 15-way MPI CSI-2 connector for Raspberry Pi HD video camera (775-7731)
- 15-way Display Serial Interface connector
- MicroSD card socket
- Boots from MicroSD card, running a version of the Linux operating system (See Note below)
- 40-pin header for GPIO and serial buses (compatible with Raspberry Pi Model A 26-pin header)
- Header footprint for JTAG connector
- Power supply: +5V @ 2A via microUSB socket
- Dimensions: 66 x 56 x 14mm