ناموجود
-
نقد و بررسی اجمالی
نمایشگر 3.5 اینچی “320x480″ مناسب
برای آردوینو UNO و Mega2560 و دارای ابعادی برابر با 3.5 اینچ است.
این نمایشگر از نوع TFT است و به همراه تاچ مقاومتی میباشد. رزولوشن آن 320X480
پیکسل است و دارای ارتباط پارالل 8 بیتی است
.
ویژگی خاص این نمایشگر داشتن تاچ اسکرین مقاومتی است که می تواند لمس
انگشتان شما را از هر نقطه ای برروی صفحه نمایش شناسایی کند همچنین دارای قلم تاچ
اسکرین مخصوص نیز میباشد که همراه برد ارسال خواهد شد.
مشخصات
نوع کانکتور پین هدر
رزولوشن 320*480
ورودی ویدیو امکان پخش فیلم وتصاویر
پروتکل ارتباطی موازی (PARALEL) 8 بیتی
پردازنده چیپ درایور ILI 9481B
رنگ صفحه نمایش رنگی
مناسب برای آردوینو UNO, MEGA2560
Introduction
Support Arduino UNO and Arduino Mega2560 and other
development board DIP, Without any wiring, all open source, Arduino libraries
offer
development board DIP, Without any wiring, all open source, Arduino libraries
offer
The backlight always on, can not control the backlight, backlight is connect to
3.3V
3.3V
DC: 5VThe control and driving circuit of TFT modules is low voltage and FRIDA
micro-power CMOS circuit, can be easily damaged by static, static damage is an
irreparable damage, and sometimes human have hundreds of volts of high voltage
static electricity, therefore, in handling, assembling and use should be
extremely careful to prevent static electricity: 1. Using
soldering iron or power FRIDA tools must be well grounded and operation, make
them without leakage;2. Do not use hand to touch the leads, circuit boards and
metal boxes;3. Do not use a vacuum cleaner for cleaning, because it generates
strong static electricity;4. When the air is dry, can also generate static
electricity, therefore, workshop humidity shall be above RH60%;5. If it is
necessary to direct contact it , should enable the human body in the same
potential with the modules? ,ormake human body be well grounded;6. Remove or back
in the bags or move locations, also need to be careful to prevent static
electricity. Don’t replace or discard the original packing.
micro-power CMOS circuit, can be easily damaged by static, static damage is an
irreparable damage, and sometimes human have hundreds of volts of high voltage
static electricity, therefore, in handling, assembling and use should be
extremely careful to prevent static electricity: 1. Using
soldering iron or power FRIDA tools must be well grounded and operation, make
them without leakage;2. Do not use hand to touch the leads, circuit boards and
metal boxes;3. Do not use a vacuum cleaner for cleaning, because it generates
strong static electricity;4. When the air is dry, can also generate static
electricity, therefore, workshop humidity shall be above RH60%;5. If it is
necessary to direct contact it , should enable the human body in the same
potential with the modules? ,ormake human body be well grounded;6. Remove or back
in the bags or move locations, also need to be careful to prevent static
electricity. Don’t replace or discard the original packing.
-
توضیحات کوتاه
شیلد نمایشگر لمسی 3.5 اینچ مخصوص آردوینو UNO و Mega2560
